TH400 Gear Ratios Explained: First, Second, Third, and Reverse

TH400 gear ratios help explain how the GM Turbo-Hydramatic 400 delivers power through its three forward gears and reverse. Whether you’re planning a classic muscle car build, a truck drivetrain upgrade, or a custom transmission swap, understanding these ratios can help you choose a suitable rear axle ratio, torque converter, and overall drivetrain combination.

The TH400 is a three-speed automatic transmission known for its straightforward gear arrangement and lack of a factory overdrive gear. Its gear ratios are relatively close to those of the later 4L80E, but the 4L80E adds a fourth overdrive gear for lower engine speed during highway cruising.

This guide covers the standard TH400 gear ratios, what each ratio does, how rear axle gearing affects overall performance, and how the TH400 compares with other common GM automatic transmissions.

TH400 gear ratio chart

The commonly published factory TH400 gear ratios are:

GearRatio
First2.48:1
Second1.48:1
Third1.00:1
Reverse2.07:1
OverdriveNone

These figures are listed in transmission gearing references, including TCI’s GM transmission ratio chart and technical transmission guides. Specific aftermarket TH400 builds may use different gearsets, so verify the specifications of a modified or performance-built transmission rather than assuming every TH400 has the original factory ratios.

What do TH400 gear ratios mean?

A transmission gear ratio describes how many times the transmission input shaft turns for each output shaft revolution in a selected gear.

For example, a 2.48:1 first gear means the input shaft turns approximately 2.48 times for every one revolution of the output shaft. This reduction multiplies torque at the transmission output while reducing output speed.

A lower numerical gear ratio, such as 1.00:1, provides less torque multiplication than a higher numerical ratio such as 2.48:1.

The TH400 uses three forward gear ratios to balance initial acceleration with engine speed as vehicle speed increases.

Understanding this distinction is useful when comparing transmissions, selecting rear axle gears, and planning a complete drivetrain.

TH400 first gear ratio: 2.48:1

The TH400 first gear ratio is 2.48:1. It provides the greatest mechanical reduction of the three forward gears.

This reduction helps the vehicle get moving from a stop by multiplying engine torque before it reaches the driveshaft and rear axle. It is particularly relevant in heavier vehicles, vehicles with larger tires, and performance applications where initial acceleration matters.

The first gear ratio works together with the rear axle ratio. A vehicle with numerically higher rear gears generally has more overall torque multiplication at the wheels than an otherwise identical vehicle with numerically lower rear gears.

However, first gear performance cannot be judged by the transmission ratio alone. Engine torque, torque converter characteristics, tire diameter, vehicle weight, and traction all influence how the vehicle accelerates.

TH400 second gear ratio: 1.48:1

The second gear ratio is 1.48:1. It provides less reduction than first gear while continuing to multiply engine torque.

When the transmission shifts from first to second, the engine speed drops because the transmission changes to a taller ratio. The size of this change affects how the engine delivers power during acceleration.

The 1.48:1 second gear is also useful when comparing the TH400 with other GM automatic transmissions. For example, the TH350 has a commonly listed second gear ratio of 1.52:1, which is slightly numerically higher than the TH400’s 1.48:1 ratio.

That difference is only one part of a transmission comparison. Vehicle weight, engine output, converter selection, internal construction, and the rest of the drivetrain also matter.

TH400 third gear ratio: 1.00:1

The TH400 third gear ratio is 1.00:1, commonly described as direct drive.

At this ratio, the transmission input and output shafts turn at the same speed in the selected gear, ignoring internal losses. The transmission is no longer providing the reduction used in first and second gear.

Third gear is important for steady-speed driving and for understanding the TH400’s highway characteristics.

Unlike a four-speed automatic with overdrive, the TH400 does not have a factory fourth gear that reduces engine speed below the transmission input speed. At a given road speed, the engine RPM therefore depends heavily on the rear axle ratio, tire diameter, and torque converter behavior.

This does not automatically make the TH400 unsuitable for highway use. It means the complete drivetrain needs to be matched to the intended driving conditions.

TH400 reverse gear ratio: 2.07:1

The commonly published TH400 reverse ratio is approximately 2.07:1. Reverse uses a separate gear arrangement to provide the direction change needed for backing up.

Reverse gearing is not an additional forward speed. It is designed for controlled vehicle movement in the opposite direction.

When reviewing transmission specifications, check that reverse is listed separately from the three forward gear ratios. This avoids confusion when comparing a TH400 with other transmissions or reviewing a technical specification sheet.

How rear axle gearing changes the overall ratio

Transmission gearing is only one part of the drivetrain equation. The rear axle ratio also multiplies the transmission ratio.

To calculate the overall ratio in a selected gear, multiply the transmission gear ratio by the rear axle ratio.

Formula:

Overall ratio = Transmission gear ratio × Rear axle ratio

For example, consider a TH400 paired with a 3.73:1 rear axle ratio.

TH400 gearTransmission ratioRear axle ratioOverall ratio
First2.483.739.25:1
Second1.483.735.52:1
Third1.003.733.73:1
Reverse2.073.737.72:1

These figures show the combined numerical reduction before accounting for torque converter multiplication, drivetrain losses, and other operating factors.

A higher numerical overall ratio provides more mechanical torque multiplication at the wheels, but it also affects engine speed at a given road speed.

Example: TH400 with 3.08, 3.55, and 3.73 rear gears

The following table compares first-gear and third-gear overall ratios with three common rear axle ratios.

Rear axle ratioFirst-gear overall ratioThird-gear overall ratio
3.08:17.64:13.08:1
3.55:18.80:13.55:1
3.73:19.25:13.73:1

With 3.73 rear gears, the vehicle has more overall first-gear reduction than it would with 3.08 gears. This can help a heavier vehicle or a performance-oriented combination accelerate from a stop.

However, the higher numerical axle ratio also increases engine RPM at a given road speed when tire diameter and transmission gear are unchanged.

The right combination depends on the engine’s operating range, tire size, vehicle weight, intended use, and desired cruising characteristics.

TH400 vs. TH350 gear ratios

The TH400 and TH350 are both three-speed GM automatic transmissions, and their factory gear ratios are relatively close.

GearTH400TH350
First2.48:12.52:1
Second1.48:11.52:1
Third1.00:11.00:1
OverdriveNoNo

The TH350 has slightly higher numerical ratios in first and second gear. Both transmissions use a 1.00:1 third gear and lack factory overdrive.

The small ratio differences do not tell the whole story when choosing between them. Their physical dimensions, weight, internal components, vehicle fitment, and intended operating conditions should also be considered.

For a replacement or performance build, verify bellhousing compatibility, driveshaft requirements, crossmember position, output shaft configuration, shifter operation, and kickdown system requirements.

TH400 vs. 4L80E gear ratios

The TH400 and 4L80E share similar commonly published ratios in their first three forward gears.

GearTH4004L80E
First2.48:12.48:1
Second1.48:11.48:1
Third1.00:11.00:1
FourthNone0.75:1
Reverse2.07:12.07:1

The most significant ratio difference is fourth gear. The 4L80E has a 0.75:1 overdrive gear, while the TH400 has only three forward speeds.

Overdrive allows the 4L80E to turn the engine at a lower speed during suitable cruising conditions compared with a direct-drive transmission using the same axle ratio and tire diameter.

The 4L80E also uses electronic controls, while the traditional TH400 uses a hydraulic control system. A conversion to a 4L80E therefore involves more than comparing gear ratios. Controller compatibility, wiring, sensors, and calibration must also be addressed.

For a build where simplicity and a traditional three-speed automatic are priorities, the TH400 may be worth considering. For a vehicle that regularly cruises at highway speeds and needs overdrive, the 4L80E offers a different set of advantages.

Does the TH400 have overdrive?

No. The standard GM TH400 is a three-speed automatic transmission without a factory overdrive gear.

Its third gear is 1.00:1, which is direct drive rather than overdrive. This is an important consideration when planning a vehicle that will spend considerable time at highway speeds.

Engine RPM at cruising speed depends on several factors:

  • Transmission gear ratio
  • Rear axle ratio
  • Tire diameter
  • Actual vehicle speed
  • Torque converter characteristics
  • Drivetrain operating conditions

A TH400 can be paired with different rear axle ratios to suit a particular vehicle, but changing the axle ratio does not add an overdrive gear.

An aftermarket auxiliary overdrive unit is another possible drivetrain approach, but it adds components, installation considerations, cost, and compatibility requirements. The specific unit and application should be evaluated before making a decision.

How TH400 gear ratios affect torque converter selection

The torque converter is an important part of a TH400 drivetrain. It transfers engine power to the transmission and allows the engine to continue running while the vehicle is stationary.

A torque converter also affects how the vehicle responds during acceleration. Its characteristics should be matched to the engine, vehicle weight, rear axle gearing, tire size, and intended driving conditions.

When choosing a TH400 torque converter, consider:

  • Engine displacement and torque characteristics
  • Vehicle weight
  • Rear axle ratio
  • Tire diameter
  • Intended street or track use
  • Transmission build specifications
  • Desired converter behavior

A higher-stall converter is not automatically better. Its suitability depends on the engine’s powerband and the vehicle’s complete combination.

A TH400 stall converter should be selected based on the actual application rather than a generic stall-speed recommendation. The converter manufacturer or transmission builder should confirm compatibility with the engine and transmission.

Do TH400 performance transmissions have different gear ratios?

Many performance TH400 transmissions retain the standard factory gear ratios, but aftermarket gearsets are also available.

For example, TCI lists several TH400 gear configurations in addition to its factory-ratio reference. These include alternative first- and second-gear combinations. This demonstrates why a buyer should not assume that every transmission described as a TH400 has identical internal gearing.

A performance transmission may also include changes to clutch packs, bands, valve-body calibration, internal supports, or other components. Those upgrades do not necessarily change the transmission’s gear ratios.

If a transmission is advertised as a Level 3 or high-performance build, ask for the actual build specifications. The level designation alone does not establish a particular gearset, horsepower rating, torque capacity, or included torque converter.

Before purchasing, confirm:

  • Whether the transmission uses factory or aftermarket gear ratios
  • Whether the transmission is built for the intended engine and vehicle
  • Whether the torque converter is included
  • Whether the unit is configured for 2WD or 4WD
  • Which bellhousing pattern and output configuration are supplied
  • What warranty and installation requirements apply

These details are more useful than relying on a performance label alone.

How to choose the right TH400 gear and axle combination

Choosing a suitable drivetrain combination starts with how the vehicle will be used.

Street-driven vehicles

For a street car, consider the balance between initial acceleration and cruising RPM. A numerically higher rear axle ratio can improve mechanical leverage in first gear, but it may also increase engine speed during highway driving.

The engine’s torque curve, tire diameter, vehicle weight, and converter characteristics should all be considered before selecting axle gearing.

Drag racing applications

A drag racing vehicle may benefit from a combination that keeps the engine within its useful powerband throughout the run.

Rear axle ratio, tire diameter, converter characteristics, and the transmission’s shift points all influence the result. The correct setup depends on the engine, vehicle weight, track conditions, and target performance.

Trucks and heavier vehicles

Heavier vehicles place different demands on the drivetrain. Engine torque, axle gearing, cooling, vehicle weight, and intended load should be considered together.

A TH400’s three-speed layout may suit some applications, but the absence of factory overdrive should be considered if the vehicle regularly travels at highway speeds.

Classic car and custom swaps

A TH400 swap requires more than matching gear ratios. Confirm the transmission’s physical configuration, bellhousing pattern, driveshaft length, crossmember position, shifter linkage, speedometer arrangement, and kickdown operation.

A 2WD transmission and a 4WD transmission may require different output shaft and tailhousing arrangements. Confirm the exact configuration before ordering.

Frequently asked questions about TH400 gear ratios

What is the stock TH400 first gear ratio?

The commonly published factory TH400 first gear ratio is 2.48:1. Some aftermarket gearsets use different ratios, so check the specifications of a modified transmission.

What is the TH400 second gear ratio?

The standard TH400 second gear ratio is 1.48:1. It provides less reduction than first gear and more reduction than third gear.

What is the TH400 third gear ratio?

The TH400 third gear ratio is 1.00:1, also known as direct drive. The input and output shafts turn at the same speed in this gear, ignoring internal losses.

What is the TH400 reverse gear ratio?

The commonly listed TH400 reverse ratio is approximately 2.07:1. Reverse is separate from the transmission’s three forward gears.

Does the TH400 have a fourth gear?

No. The standard TH400 is a three-speed automatic without factory overdrive. Its highest forward gear is third at 1.00:1.

Is the TH400 gear ratio the same as the 4L80E?

The first three commonly published forward gear ratios are the same: 2.48:1, 1.48:1, and 1.00:1. The 4L80E adds a fourth gear with a 0.75:1 overdrive ratio.

Is the TH400 ratio better than the TH350 ratio?

Neither transmission is automatically better based on ratios alone. The TH350 has slightly higher numerical first- and second-gear ratios, while both transmissions have a 1.00:1 third gear and no factory overdrive. The right choice depends on the vehicle, engine, fitment, and intended use.

Can you change the gear ratios in a TH400?

Yes. Aftermarket gearsets are available for certain TH400 applications. Changing the ratios requires compatible internal components and professional transmission assembly. Confirm the gearset’s specifications before purchasing or rebuilding a transmission.

What rear axle ratio works well with a TH400?

There is no single rear axle ratio that works for every TH400 application. The appropriate ratio depends on vehicle weight, engine output, tire diameter, converter characteristics, and driving conditions. Calculate the overall gearing and consider cruising RPM before selecting an axle ratio.

Final considerations

The standard TH400 gear ratios—2.48:1 first, 1.48:1 second, and 1.00:1 third—give the transmission a straightforward three-speed layout. Its lack of factory overdrive is an important consideration when choosing a transmission for a street car, truck, or performance build.

The best results come from matching the transmission to the complete drivetrain rather than choosing gear ratios in isolation. Rear axle gearing, tire diameter, torque converter characteristics, engine powerband, and vehicle use all influence how the finished combination performs.

When comparing a standard TH400 with a performance-built unit, confirm the actual internal specifications, configuration, and included components before making a purchase.

Leave a Reply

Your email address will not be published. Required fields are marked *